How To Repair An Iphone 5s Screen

Introduction

Acquire how to replace your iPhone 5 screen. This part comes with the front-facing camera, earpiece speaker and LCD shield plate already installed, making for an easier repair.

All you need to do is remove the old screen and transfer the home button to the new screen.

After successfully replacing the screen, protect information technology from scratches by installing a screen protector.

Video Overview

• If your brandish glass is cracked, keep farther breakage independent and prevent bodily harm during your repair past taping the drinking glass.

• Lay overlapping strips of clear packing tape over the iPhone's display until the whole confront is covered.

• This will keep glass shards contained and provide structural integrity when prying and lifting the display.

• Wear safety spectacles to protect your eyes from whatever drinking glass shaken free during the repair.



• Before you lot proceed, belch your iPhone battery beneath 25%. A charged lithium-ion battery can take hold of fire and/or explode if accidentally punctured.

• Power off your iPhone earlier outset disassembly.

• Remove the 2 3.6 mm Pentalobe screws next to the Lightning connector.

• In the post-obit steps you will be pulling the display upwards out of the telephone body. The brandish is composed of a glass screen and a plastic bezel with metal clips.

• Regardless of the tool you apply, you need to be sure you pull up the unabridged display.

• If the glass begins to split up from the plastic, as shown in the start image, slide a plastic opening tool between the plastic frame and the metal phone body to pry the metal clips out of the case.

• If you are reassembling a phone with a separated brandish bezel, you lot may desire to place a sparse strip of adhesive between the plastic bezel and the glass to proceed the phone closed.

• The adjacent two steps demonstrate using the iSclack, a great tool for safely opening the iPhone 5 that nosotros recommend for anyone doing more than one repair. If y'all aren't using the iSclack, skip to Step 6.

• Close the handle on the iSclack, opening the suction-cup jaws.

• Place the bottom of your iPhone in between the suction cups, confronting the plastic depth guess.

• The top suction cup should residuum just higher up the home push.

• Open the handles to close the jaws of the iSclack. Centre the suction cups and printing them firmly onto the top and bottom of the iPhone.

• Concur onto your iPhone securely and close the handle of the iSclack to separate the suction cups, pulling the front end console upwardly from the rear case.

• The iSclack is designed to safely open up your iPhone just enough to separate the pieces, but not enough to damage whatever cables.

• Peel the two suction cups off your iPhone.

• Skip the next iii steps and continue on Step 9.

• Press a suction loving cup onto the screen, but in a higher place the home button.

• Be sure the loving cup is completely on the screen to get a tight seal.

• If y'all're opening an iPhone with cracked glass, neatly lay a couple strips of packing tape beyond the forepart and squeeze out as many bubbles every bit you can. This will give the suction cup a surface to grab, and minimize the spread of broken glass.

• Brand sure the suction cup is firmly attached to the front console assembly.

• While holding the iPhone downward with one hand, pull up on the suction loving cup to slightly separate the front end panel associates from the rear case.

• Take your time and employ firm, abiding force. The screen is a much tighter fit than most devices.

• With a plastic opening tool, begin to gently pry the rear example down, away from the screen, while you pull upward with the suction cup.

• In that location are several clips attaching the front panel assembly to the rear case, and so you may need to employ a combination of the suction cup and plastic opening tool to free the front panel assembly.

• Continue to pry up around the sides of the front console assembly, detaching the clips along the left and right side.

• Do not try to completely remove the front panel associates from the rear example, as there are several ribbon cables still attached at the superlative of the iPhone.

• In one case the clips have been released on the bottom and sides of the front panel associates, pull the bottom of the associates away from the rear case.

• Open the brandish to about a 90º bending, and lean it confronting something to keep it propped upward while you're working on the phone.

• Add a rubber ring to keep the display securely in identify while you work. This prevents undue strain on the display cables.

• Remove the following two screws securing the metal battery connector bracket to the logic board:

• Ane i.viii mm Phillips spiral

• One 1.half dozen mm Phillips spiral

• Remove the metal battery connector bracket from the iPhone.

• Use a plastic opening tool to gently pry the bombardment connector upward from its socket on the logic board.

• Be careful not to dislodge the pocket-size surface-mounted components surrounding the socket.

• Be very conscientious to only pry upwards on the battery connector itself and non the socket on the logic board. If you pry up on the logic board socket or the board itself, yous may destroy the socket or harm nearby components on the board.

• Remove the following screws securing the front panel assembly cablevision bracket to the logic board:

• Two i.2 mm Phillips screws

• I one.6 mm Phillips screw

• This screw tends to not exist attracted to a magnetized screwdriver. Have care not to lose it when removing, and make certain it gets back into the right identify—a magnetized spiral may interfere with the compass.

• Lift the brandish cable bracket toward the battery to unhook it, and remove it from the iPhone.

• During reassembly, clip the left-hand hooks under the logic lath and lower the bracket towards the outside of the phone.

• Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.

• Employ a plastic opening tool or a fingernail to disconnect the three front panel assembly cables:

• Forepart-facing camera and sensor cable

• LCD cable

• Digitizer cable

• When reassembling your telephone, the LCD cable may pop off the connector. This can cause white lines, or goose egg at all to appear when powering your telephone back on. If that happens, merely reconnect the cablevision and power cycle your phone. The all-time fashion to power bike your phone is to disconnect and reconnect the battery.

• Remove the front panel assembly from the rear instance.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Squad

Embed this guide

Choose a size and copy the lawmaking beneath to embed this guide as a small-scale widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iPhone+5+Screen+Replacement/10588

Share this post